This kit makes amplifier installation a breeze for the beginner or seasoned professional. Complete kit includes all the hardware and wire needed to install a high powered amplifier system in the trunk or back compartment of your car, small SUV, or jeep. Includes 16 ft. high quality low signal loss shielded RCA stereo patch cable, 20 ft. of 8 ga. high current power cable, 4 ft. of 8 ga. ground cable, 16 ft. of 18 ga. remote turn-on wire, 3 ft. of 1/4" split loom tubing to hide your wires, water resistant in-line AGU fuseholder w/60 amp fuse, gold ring and spade terminals for 8 ga. wire, butt splices, 4" cable ties, and detailed instructions. Perfect for amplifiers up to 400 watts.
PYLE amplifiers are designed with the lastest technology available, incorporating a Dc to Dc switching power supply, which provides headroom for even the most demanding peaks and dynamic range found on modern CD's and recordings.
Specifications: *Power output: 100 watts RMS/400 watts max x 2 (4ohm load), 175 watts RMS x 2 (2 ohm load) *Total Harmonic Distortion: < .04% *Signal to Noise ratio (S/N): > 90 dB *Input sensitivity: 100 mV~4 V *Channel separation: > 65 dB *Frequency response: 10-30,000 Hz *One-year manufacturer's warranty *Dimensions: 7"W x 2-1/4"H 8-5/8"L.
Remote bass level control
Electronic crossover network (low pass / full range / high pass)
PYLE amplifiers are designed with the lastest technology available, incorporating a Dc to Dc switching power supply, which provides headroom for even the most demanding peaks and dynamic range found on modern CD's and recordings.
Specifications: *Power output: 150 watts RMS/500 watts max x 2 (4ohm load), 250 watts RMS x 2 (2 ohm load) *Total Harmonic Distortion (THD): < .04% *Signal to Noise ratio (S/N): > 90 dB *Input sensitivity: 100 mV~4 V *Channel separation: > 65 dB *Frequency response: 10-30,000 Hz *One-year manufacturer's warranty *Dimensions: 8-11/16"W x 2-1/4"H 8-5/8"L.
PYLE amplifiers are designed with the lastest technology available, incorporating a Dc to Dc switching power supply, which provides headroom for even the most demanding peaks and dynamic range found on modern CD's and recordings.
Specifications: *Power output: 250 watts RMS/800 watts max x 2 (4ohm load), 400 watts RMS x 2 (2 ohm load) *Total Harmonic Distortion (THD): < .04% *Signal to Noise ratio (S/N): > 90 dB *Input sensitivity: 100 mV~4 V *Channel separation: > 65 dB *Frequency response: 10-30,000 Hz *One-year manufacturer's warranty *Dimensions: 9-7/8"W x 2-1/4"H 8-5/8"L.
Remote bass level control
Electronic crossover ( high pass / full range / low pass )
PYLE amplifiers are designed with the lastest technology available, incorporating a Dc to Dc switching power supply, which provides headroom for even the most demanding peaks and dynamic range found on modern CD's and recordings.
Specifications: *Power output: 500 watts RMS/1000 watts max x 2 (4ohm load), 700 watts RMS x 2 (2 ohm load) *Total Harmonic Distortion (THD): < .04% *Signal to Noise ratio (S/N): > 90 dB *Input sensitivity: 100 mV~4 V *Channel separation: > 65 dB *Frequency response: 10-30,000 Hz *One-year manufacturer's warranty *Dimensions: 17-11/16"W x 2-1/4"H 8-5/8"L.
Remote bass level control
Electronic crossover ( high pass / full range / low pass )
PYLE amplifiers are designed with the lastest technology available, incorporating a Dc to Dc switching power supply, which provides headroom for even the most demanding peaks and dynamic range found on modern CD's and recordings.
Specifications: *Power output: 600 watts RMS x 1 (4 ohm load), 1,800 watts max x 1 (2 ohm load), 3,600 watts max x 1 (1.3 ohm load) *1 ohm stable *Frequency response: 15-150 Hz *Variable low pass crossover: 50~150 Hz (24 dB/octave) *Variable subsonic filter: 15~40 Hz (24 dB/octave) *Total Harmonic Distortion (THD): < 0.1% *Signal to noise ratio (S/N): > 90 dB *Phase control: 0~180° *One-year manufacturer's warranty *Dimensions: 12-11/16" L x 8-5/8" W x 2-1/4" H.
PYLE amplifiers are designed with the lastest technology available, incorporating a Dc to Dc switching power supply, which provides headroom for even the most demanding peaks and dynamic range found on modern CD's and recordings.
Specifications: *Power output: 100 watts RMS/250 watts max x 4 (4ohm load), 150 watts RMS x 4 (2 ohm load) *Total Harmonic Distortion (THD): < .04% *Signal to Noise ratio (S/N): > 90 dB *Input sensitivity: 100 mV~4 V *Channel separation: > 65 dB *Frequency response: 10-30,000 Hz *One-year manufacturer's warranty *Dimensions: 11-3/8"W x 2-1/4"H 8-5/8"L.
Remote bass level control
Electronic crossover ( high pass / full range / low pass )
PYLE amplifiers are designed with the lastest technology available, incorporating a Dc to Dc switching power supply, which provides headroom for even the most demanding peaks and dynamic range found on modern CD's and recordings.
Specifications: *Power output: 200 watts RMS/500 watts max x 4 (4ohm load), 350 watts RMS x 4 (2 ohm load) *Total Harmonic Distortion (THD): < .04% *Signal to Noise ratio (S/N): > 90 dB *Input sensitivity: 100 mV~4 V *Channel separation: > 65 dB *Frequency response: 10-30,000 Hz *One-year manufacturer's warranty *Dimensions: 12-5/8"W x 2-1/4"H 8-5/8"L.
Remote bass level control
Electronic crossover ( high pass / full range / low pass )
PYLE amplifiers are designed with the lastest technology available, incorporating a Dc to Dc switching power supply, which provides headroom for even the most demanding peaks and dynamic range found on modern CD's and recordings.
Specifications: *Power output: 100 watts RMS x 4 + 250 watts RMS x 2 (4ohm load), 175 watts RMS x 4 + 400 watts RMS x 1 (2ohm load), 400 watts max x 2 + 900 watts max x 1 (4ohm load) *Total Harmonic Distortion (THD): < .04% *Signal to Noise ratio (S/N): > 90 dB *Input sensitivity: 100 mV~4 V *Channel separation: > 65 dB *Frequency response: 10-30,000 Hz *One-year manufacturer's warranty *Dimensions: 19-11/16"W x 2-1/4"H 8-5/8"L.
Remote bass level control
Electronic crossover ( high pass / full range / low pass )
The center channel speaker is magnetically shielded for safe positioning on or near a television or computer monitor. The powered subwoofer features a long-throw woofer, built-in 60-watt amplifier, front-ported enclosure, two RCA line-level inputs, speaker-level inputs/outputs, and variable gain control for optimal level matching with the rest of the system. Center channel and satellites are housed in attractive, durable, low resonance black ABS cabinets and their small size allows them to blend into and decor. Limited availability factory buyout. Large quantity available.
Transform your boring TV room into a sonically superior home theater
Complete system includes 5 compact speakers and a 60 watt powered subwoofer
Magnetically shielded center channel can be placed directly on TV or monitor
RCA line-level and speaker level inputs on subwoofer
Specifications:
Center channel: •Driver: 3-1/2" coaxial •Frequency response: 120 Hz-20 kHz (±3 dB) •Impedance: 4 ohms •Recommended max amplifier power: 60 watts RMS •SPL: 91 dB •Dimensions: 4.6" H x 4.3" W x 4.2" D.
Satellite speakers: •Driver: 3-1/2" coaxial •Frequency response: 120 Hz-20 kHz (±3 dB) •Impedance: Front speakers: 4 ohms; Rear speakers: 8 ohms •Recommended max amplifier power: 60 watts RMS •SPL: Front speakers: 91 dB; Rear speakers: 89 dB •Dimensions: 4.6" H x 4.3" W x 4.2" D.
Subwoofer: •Woofer: Long-throw 5-1/4" *Frequency response: 50-200 Hz (±3 dB) •Amplifier power output: 30 watts RMS, 60 watts max •Forward firing port tuned enclosure •Wood cabinet with attractive ABS front •Two RCA low-level inputs •Hi-level inputs/outputs •Variable gain control •Dimensions: 10.1" H x 7.5" W x 14.2" D.
View programming from two or three satellites with one dish! Mount two brackets for up to 30+ degrees of coverage without moving the dish.
View FTA FSS programming and Dish or DirecTV on a single dish. Add a DiSEqC switch and your receiver will instantly and seamlessly switch between channels on different satellites. Fits most popular dishes including GEOSATpro, Winegard and Fortec Star. Accepts any standard 40mm LNBF (lnbf not included).
Note: Most 40mm LNBFs allow reception of satellites spaced as close as 5 degrees. Reception of multiple satellites spaced less than 5 degrees may be possible with reduced signal quality.
The all new 63-BSC621-DMS C/Ku LNBF is now in stock. This LNBF works can work with any receiver that provides voltage switching for polarity control, including 4DTV. Please note, the 63-BSC621-2-DMS is universal Ku and cannot work with 4DTV because the receiver does not have universal switching abilities. If you own a 4DTV make sure your order the 63-BSC621-DMS.
This model is not recommended for use with a Motorola 4DTV or any other cband receiver. For use with these receivers take a look at our other model the Combined C KU-Band LNBF which has a Ku Lo 10750 & C 5150
Mount C-Band LNBFs on a 1.2 or 1.8 Meter Offset Dish!
Now you can view C-Band programming on your GEOSATpro 1.2 meter or 1.8 meter dish. Add hundreds of additional analog and digital channels of free programming, network feeds, sporting events, breaking news, back-hauls, televison and radio services are available.
This bracket allows the mounting of a C-Band LNB or LNBF on GEOSATpro 1.2 or 1.8 meter dishes.
Bracket shown with available C-Band LNBF (not included)
Circular LNBF Suggested Retail Price $35.00 FREQUENCY RANGE HIGH BAND 12.2 ~ 12.7 GHz L.O. FREQUENCY 950 ~ 1450 MHz Noise Figure 0.7dB(max) Conversion Gain 55 dB Gain Flatness 1 dB(max) at 24 MHz intervals Gain Variation 5 dB(max) across 500 MHz Cross Polarization Isolation 25dB (min) Local Oscillator Frequency Stability 11250 +/- 3 MHz (max.), over temperature and life Phase Noise 50dBc/Hz @ 1 KHz -75dBc/Hz @ 10KHz -95dBc/Hz @ 100 KHz Output VSWR 2:1(max) @ 75 ohm Image Rejection 40dB (min.) Po 1dB 0 dBm(min) 3rd Order Intermodulation -50 dBc(max), two tones of ˇV15 dBm output spaced 27 MHz Polarity Switching Voltage 10 ~ 14V at RHCP 15 ~ 21V at LHCP DC Current Consumption 165 mA(max) Operating Temperature Range -35 degrees C ~ +50 degrees C
C-Band and KU-Band Linear Standard LNBF C/Ku LNBF GSL1C/KAvailable Now!!!!
Geosatpro has produced in cooperation with one of the World's leading LNB manufacturer an LNBF that simultaneously receives both C-band and Ku-band linear signals. Expand your viewing options with the ability to view programming from C-band and Ku-band satellites on one dish! Hundreds of additional digital signals are available on these two bands. Hobbyist report success with smaller 1.2M dishes, but we recommend a 2.4M minimum dish size.
Includes standard scaler for 3 or 4 point prime focus mounting.
GeoSatpro Standard Single .4 LNBF Suggested Retail Price $20.00 For Reception of North American Satellites 11.70 - 12.20 GHz New reduced low noise figure of .4 dB and 55 dB gain are combined in this frequency stable, quality lnb. This LNBF is one of the most reliable "of the shelf" LNBFs that we have ever carried. Failure rate of less than 1/10th of 1% means less service calls, less RMAs and better profits! Standard LNBFs work with all satellite meters and make installs easier. Perfect viewing linear satellites in North America. Technical Specifications Input Frequency Range 11.70 - 12.20 GHz L.O. Frequency 10.75 GHz L.O. Stability 2 MHz (-40 - +70° c) Ouput Frequency Range 950 - 1450 MHz Noise .4 dB typical Conversion Gain 55 dB typical Input VSWR 2.5:1 Output VSWR 2.0:1 (max) Connector F Type female Impedence 75 ohm typical Cross Polar Isolation 20dB (min.) Image Rejection 45 dB (min.) Phase Noise -50dBc @ 1 KHz -75dBc @ 10 KHz -95dBc @ 100KHz Supply Voltage Ca: 11. - 14.0 V = Vertical Polarization Cb: 16.0 - 20.0 V = Horizontal Polarization Operating Temperature -40 - +70 degrees Celsius Storage Temperature -40 - +80 degrees Celsius Relative Humidity 0 - 95 % Throat Diameter 40mm Size 5 1/4" x 2" x 2" Weight 7 1/2 onces
GeoSatpro Standard Twin .4 LNBF Suggested Retail Price $35.00 For Reception of North American Satellites 11.70 - 12.20 GHz Low noise 0.4 dB and high gain 55dB are combined in this frequency stable, quality lnb. We have not received a single report of product failure or poor performance! This LNBF outperforms most single LNBFs and will provide your customers years of dependable service. We will back up this statement by offering a Two Year replacement warranty! Two outputs can either feed two receivers directly or into a multi-switch for multiple receivers. The housing provides additional protection to the cable connections with a cover that slides over the fittings. Standard LO 10750 LNBFs are the easiest to install and work with all satellite meters and receivers. Perfect for multiple receiver installations for the reception of linear satellites in North America. Technical Specifications Input Frequency Range 11.70 - 12.20 GHz L.O. Frequency 10.75 GHz L.O. Stability 2 MHz (-40 - +70° c) Ouput Frequency Range 950 - 1450 MHz Noise 0.4 dB typical Conversion Gain 55 dB typical Input VSWR 2.5:1 Output VSWR 2.0:1 (max) Connector F Type female Impedence 75 ohm typical Cross Polar Isolation 20dB (min.) Image Rejection 45 dB (min.) Phase Noise -50dBc @ 1 KHz -75dBc @ 10 KHz -95dBc @ 100KHz Supply Voltage Ca: 11.0 - 14.0 V = Vertical Polarization Cb: 16.0 - 19.0 V = Horizontal Polarization Operating Temperature -40 - +70 degrees Celsius Storage Temperature -40 - +80 degrees Celsius Relative Humidity 0 - 95 % Throat Diameter 40mm Size 5 1/4" x 2" x 2" Weight 7 1/2 onces
.jpg)
.jpg)
.jpg)
.jpg)
